SAFETY DATA SHEET

PELCO Pro CA44 Tissue Adhesive

Version 1Last reviewed 26 February 2026Catalogue: 10033, 14460, 14464, 14465, 14470, 14474, 14477, 14478 PELCO PRO CA44, C100, C1000. CA-GEL CYANOACRYLATE GLUE, C300, C5, PEL10033

1. Identification

Product Identifiers

Product Name: PELCO Pro CA44 Tissue Adhesive
Other Names: Super Glue, Instant Adhesive, Cyanoacrylate
Product Number(s): 10033, 14460, 14464, 14465, 14470, 14474, 14477, 14478 PELCO PRO CA44, C100, C1000. CA-GEL CYANOACRYLATE GLUE, C300, C5, PEL10033
CAS Number: Not available

Recommended use of the chemical and restriction on use

Laboratory use.

Company Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

Emergency Contact Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

2. Hazards Identification

Classification of the substance or mixture

GHS07
Eye Irrit. 2 H319 Causes serious eye irritation.
STOT SE 3 H335 May cause respiratory irritation.
Skin Irrit. 2 H315 Causes skin irritation.

Label Elements

Signal Words: Warning
Hazard Statement(s): H319 Causes serious eye irritation.
H335 May cause respiratory irritation.
H315 Causes skin irritation.
EUH202 "Cyanoacrylate. Danger. Bonds skin and eyes in seconds. Keep out of reach of children."
Precautionary Statement(s): P280 Wear protective gloves/protective clothing/eye protection/face protection.
P340±340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P332±313 If skin irritation occurs: Get medical advice/attention.
P305±351±338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P403±233 Store in a well-ventilated place. Keep container tightly closed.
P501 Dispose of contents/container as hazardous or special waste.

Primary route(s) of entry

Not available

Human Health

Inhalation: No further information available.
Ingestion: No further relevant information available.
Eyes: No further relevant information available.
Skin: No further relevant information available.

Environment

No further relevant information available.

3. Composition / Information on Ingredients

Name	CAS No.	Content (w/w)	Classification
Ethyl-2-cyanoacrylate	7085-85-0	80-99%	Not Available

4. First Aid Measures

Ingestion: Ensure that breathing passages are not obstructed. The product will polymerise immediately in the mouth making it almost impossible to swallow. Saliva will slowly separate the solidified product from the mouth (several hours).
Inhalation: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. If still feeling unwell seek medical attention.
Skin Contact: IF ON SKIN: Wash with plenty of soap and water. Do not pull bonded skin apart. It may be gently peeled apart using a blunt object such as a spoon, preferably after soaking in warm soapy water. Cyanoacrylates give off heat on solidification. In rare cases a large drop will generate enough heat to cause a burn. Burns should be treated normally after the adhesive has been removed from the skin. If lips are accidentally stuck together apply warm water to the lips and encourage maximum wetting and pressure from saliva inside the mouth. Peel or roll lips apart. Do not try to pull the lips apart with direct opposing action. If skin irritation occurs: Get medical advice/attention.
Eye Contact: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If the eye is bonded closed, release eyelashes with warm water by covering with wet pad. Cyanoacrylate will bond to eye protein and will cause periods of weeping which will help to debond the adhesive. Keep eye covered until debonding is complete, usually within 1-3 days. Medical advice should be sought in case solid particles of cyanoacrylate trapped behind the eyelid cause any abrasive damage.
Other Information: Call a POISON CENTER or doctor/physician if you feel unwell.

5. Firefighting Measures

Suitable extinguishing equipment

Fire: Dry powder, foam, carbon dioxide, fine water spray.
Unsuitable extinguishing agents: water jet.
HAZCHEM: Trace amounts of toxic fumes may be release on incineration.
Hazardous combustion products: oxides of carbon, oxides of nitrogen, irritating organic vapours.

Special protective equipment and precautions for fire fighters

Fire fighters should wear positive pressure self-contained breathing apparatus (SCBA) and suitable protective clothing.

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures: Ensure adequate ventilation. Wear protective gloves/protective clothing/eye protection/face protection. Avoid skin and eye contact. Avoid breathing dust/fume/gas/mist/vapours/spray.
Environmental precautions: Do not let product enter drains.
Methods and materials for containment and clean up: Do not use clothes for mopping up. Flood with water to complete polymerisation and scrape off the floor. Cured material can be disposed of as non-hazardous waste.
Dispose of waste according to Federal, State and Local Regulations.

7. Handling and Storage

Precautions for safe handling: Avoid breathing dust/fume/gas/mist/vapours/spray. Use only outdoors or in a well-ventilated area. Ventilation (low level) is recommended when using large volumes. Use of dispensing equipment is recommended to minimize risk of skin or eye contact. Wash hands thoroughly after handling.
Conditions for safe storage: For optimum shelf life store in original containers under refrigerated conditions at 2 DegC to 8 DegC. Store locked up.

8. Exposure Controls / Personal Protection

Exposure Standards

Engineering controls: Provide adequate ventilation in area of use. Do NOT use this product in an enclosed or poorly ventilated area. Local exhaust ventilation is normally required when handling or using this product to keep airborne powder below the nationally authorised limits. If ventilation alone cannot control exposure, respiratory protection must be worn.

Personal protective equipment

Eye and face protection: Wear protective glasses.
Skin protection: Protective gloves: in circumstances where there is potential for prolonged or repeated skin contact, the use of polyvinyl chloride or nitrile rubber gauntlets or equivalent solvent resistant gloves is recommended. The use of chemical resistant gloves such as Nitrile is recommended. Polyethylene or polypropylene gloves are recommended when using large volumes. Do Not use PVC, rubber or nylon or cotton gloves.
Body protection: Good industrial hygiene practices should be observed. Take off contaminated clothing and wash it before reuse. Wash hands thoroughly after handling.
Respiratory protection: Ensure adequate ventilation.

9. Physical and Chemical Properties

General information

Appearance: Transparent, colourless liquid
Odour: Pungent
pH: Not determined
Vapour Pressure: <21Pa
Density: Not determined
Boiling Point: 214°C
Melting Point: -31°C
Solubility: <0.024 mg/l
Specific Gravity of Density: 1.043 b/cm³ at 20°C
Flash Point: 82.5°C
Flammable (Explosive) Limits: Not determined
Ignition Temperature: 480°C
Formula: Not available

10. Stability and Reactivity

Reactivity: No further information available.
Chemical stability: Stable under normal conditions of storage and use.
Possibility of hazardous reactions: Hazardous Decomposition Products: Oxides of carbon, oxides of nitrogen.
Hazardous Polymerization: Will not occur.
Conditions to avoid: Moisture, humidity, basic material.
Incompatible materials: Water, soil, amines, alkalis, and alcohols.

11. Toxicological Information

Acute effects: Oral: LD50 (oral, rat) >5000 mg/kg bw (OECD 401)
Dermal: LD50 (dermal, rabbit) >2000 mg/kg bw (OECD 402)
Inhalation: In dry atmosphere with <50% humidity, vapours may irritate the eyes and respiratory system.
Prolonged exposure to high concentration of vapours may lead to chronic effects in sensitive individuals.
Eye contact: Irritating to eyes. In dry atmosphere (RH<50%) vapours may cause irritation and lachrymatory effect.
Skin contact: Causes skin irritation.
Ingestion: No further information available.
Inhalation: Due to polymerization at the skin surface allergic reaction is not considered possible. The polymerised material is not able to penetrate into the epidermis.
Toxicity and irritation: No further information available.

12. Ecological Information

Ecotoxicity: Low ecotoxicity.
Persistence and degradability: NA (the test compound would polymerise with contact of water or the moisture of the soil immediately).
Bioaccumulative potential: NA (in presence of moisture ethyl-2-cyanoacrylate polymerises within seconds).
Other adverse effects: No further relevant information available.

13. Disposal Considerations

General information

Cured adhesive: Dispose of as water insoluble non-toxic solid chemical in authorised landfill or incinerate under controlled conditions.
Dispose of in accordance with local and national regulations. Polymerize by adding slowly to water (10:1). Contribution of this product to waste is very insignificant in comparison to article in which it is used.
After use, tubes, cartons and bottles containing residual product should be disposed of as chemically contaminated waste in an authorised legal land fill site or incinerated.
Federal, State and Local Laws governing disposal of materials can differ. Ensure proper disposal compliance with proper authorities before disposal.

14. Transport Information

ADG label required

HAZCHEM: Trace amounts of toxic fumes may be release on incineration.
Hazardous combustion products: oxides of carbon, oxides of nitrogen, irritating organic vapours.
UN Number: No further information available
Proper shipping name: Unrestricted, combustible liquid
Transport hazard class: No further information available.
Packing group: No further information available.
Environmental hazard: No
Special precautions for users: No further information available.
Additional information: No further information available.

15. Regulatory Information

Poisons Schedule Number: Not determined.
Other Information: No further relevant information available.

16. Other Information

SDS preparation date: 26 February 2026
Comments: This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.