SAFETY DATA SHEET

Technovit® H7100 GMA Embedding Kit - Liquid

Version 1Last reviewed 1 March 2026Catalogue: 14653 1, C031 1

1. Identification

Product Identifiers

Product Name: Technovit H7100 GMA Embedding Kit - Liquid
Other Names: TECHNOVIT 7100 - LIQUID
Product Number(s): 14653 1, C031 1
CAS Number: -

Recommended use of the chemical and restriction on use

Laboratory use.
Laboratory chemicals.

Company Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

Emergency Contact Details

ProSciTech Pty Ltd
11 Carlton Street
KIRWAN QLD 4817
Australia
(07) 4773 9444
pst@proscitech.com
proscitech.com.au

2. Hazards Identification

Classification of the substance or mixture

GHS07
Skin Irrit. 2 H315 Causes skin irritation.
Eye Irrit.2 H319 Causes serious eye irritation.
Skin Sens. 1 H317 May cause an allergic skin reaction.

Label Elements

Signal Words: Warning
Hazard Statement(s): Causes skin irritation.
Causes serious eye irritation.
May cause an allergic skin reaction.
Precautionary Statement(s): Avoid breathing dust/fume/gas/mist/vapours/spray.
Wear protective gloves.
Wear eye protection / face protection. Wash thoroughly after handling.
Contaminated work clothing should not be allowed out of the workplace.

Primary route(s) of entry

Not available.

Human Health

Inhalation: Not available.
Ingestion: Not available.
Eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
Specific treatment (see on this label).If eye irritation persists: Get medical advice/attention.
Skin: If skin irritation or rash occurs: Get medical advice/attention.
Wash with plenty of water. Take off contaminated clothing and wash it before reuse.

Environment

Dispose of contents/container in accordance with local/regional/national/international regulations.

3. Composition / Information on Ingredients

Name	CAS No.	Content (w/w)	Classification
2-hydroxyethyl methacrylate	868-77-9	50-100%	-

4. First Aid Measures

Ingestion: If symptoms persist consult doctor.
Inhalation: Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation.
Skin Contact: Immediately wash with water and soap and rinse thoroughly.
Eye Contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor.
Other Information: No further relevant information available.

5. Firefighting Measures

Suitable extinguishing equipment

Fire: CO₂, powder or water spray. Fight larger fires with water spray or alcohol resistant foam.
HAZCHEM: Not available.

Special protective equipment and precautions for fire fighters

No special measures required.

6. Accidental Release Measures

Personal precautions, protective equipment and emergency procedures: Not required.
Environmental precautions: Do not allow to enter sewers/ surface or ground water.
Methods and materials for containment and clean up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Ensure adequate ventilation.

7. Handling and Storage

Precautions for safe handling: Ensure good ventilation/exhaustion at the workplace. Prevent formation of aerosols.
Conditions for safe storage: Keep container tightly sealed.
Store in a well-ventilated place. Keep cool.

8. Exposure Controls / Personal Protection

Exposure Standards

Engineering controls: Store in a well-ventilated place. Keep cool.

Personal protective equipment

Eye and face protection: Tightly sealed goggles.
Avoid contact with the eyes and skin.
Skin protection: Protective gloves.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation.
Material of glove.s
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application.
Penetration time of glove material.
The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed.
Body protection: Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing.
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Respiratory protection: In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use self-contained respiratory protective device.

9. Physical and Chemical Properties

General information

Appearance: Colourless fluid
Odour: Characteristic
pH: Not determined.
Vapour Pressure: Not determined.
Density: 1.1 g/cm³
Boiling Point: 205 °C
Melting Point: Undetermined.
Solubility: Not miscible or difficult to mix with water.
Specific Gravity of Density: Not determined.
Flash Point: 97 °C
Flammable (Explosive) Limits: Not determined
Ignition Temperature: Product is not selfigniting.
Formula: Not available.

10. Stability and Reactivity

Reactivity: No further relevant information available.
Chemical stability: No decomposition if used according to specifications.
Possibility of hazardous reactions: No dangerous reactions known.
Conditions to avoid: No further relevant information available.
Incompatible materials: No further relevant information available.

11. Toxicological Information

Acute effects: The product shows the following dangers according to the calculation method of the General EU Classification Guidelines for Preparations as issued in the latest version:
Irritant.
Eye contact: Irritating effect.
Skin contact: Irritant to skin and mucous membranes.
Sensitisation possible through skin contact.
Ingestion: No further relevant information available.
Inhalation: Irritant to skin and mucous membranes.
Toxicity and irritation: LD/LC50 values relevant for classification:
868-77-9 2-hydroxyethyl methacrylate
Oral LD50 5050 mg/kg (rat)

12. Ecological Information

Ecotoxicity: No further relevant information available.
Persistence and degradability: No further relevant information available.
Bioaccumulative potential: No further relevant information available.
Other adverse effects: Water hazard class 1 (German Regulation) (Self-assessment): slightly hazardous for water Do not allow undiluted product or large quantities of it to reach ground water, water course or sewage system.

13. Disposal Considerations

General information

Must not be disposed together with household garbage. Do not allow product to reach sewage system.
Uncleaned packaging: ·
Recommendation: Disposal must be made according to official regulations.

14. Transport Information

ADG label required

HAZCHEM: Not available.
UN Number: None.
Proper shipping name: Not regulated.
Transport hazard class: 0
Packing group: None.
Environmental hazard: Not applicable.
Special precautions for users: Not applicable.
Additional information: No information available.

15. Regulatory Information

Poisons Schedule Number: All substances have the value S5.
Other Information: No further relevant information available.

16. Other Information

SDS preparation date: 1 March 2026
Comments: This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship.